Lenovo South Africa Channel Awards 2
Lenovo South Africa Channel Awards
Congratulations to our Server Team. Distributor of The Year!
ThinkSystem Tower Servers
Modernize to boost your business with Windows Server 2022.
Think Big. Think Lenovo. ThinkSystem Tower Servers.
Lenovo F1

INFRASTRUCTURE TEAM

+27 (0) 11 237 1000

INFRASTRUCTURE TEAM

Molex
AFR-00504L

Molex
12 Fiber Multimode OM4 BI Duplex SC Aqua Low Loss
Fibre assembly for structured cabling

SKU AFR-00504L Category Brand:
Share

Molex AFR-00504L 12 Fiber Multimode OM4 BI Duplex SC Aqua Low Loss

The Molex AFR-00504L is a multimode fibre assembly with twelve fibres, OM4 grade, bend-insensitive (BI) construction, duplex SC connectors and an aqua jacket. It is listed in the Molex datasheet range for fibre components used in structured cabling, and it is intended for fibre links inside buildings where dependable optical performance and simple installation matter.

Product overview

Structured cabling relies on well-organised fibre connections between distribution points, patch panels and active equipment. This assembly provides a pre-terminated multimode fibre solution for those links, so installers can spend less time on field termination and more time on a neat, tested installation. The description identifies it as a low-loss product, which points to a design aimed at keeping optical losses in the link low.

Key features and specifications

  • Fibre count: 12 fibres
  • Fibre type: multimode, OM4 grade
  • Construction: bend-insensitive (BI)
  • Connectors: duplex SC
  • Jacket colour: aqua, the usual colour for multimode fibre
  • Performance: described as low loss
  • Manufacturer: Molex, structured-cabling range

Exact attenuation values, lengths, jacket ratings and connector polish grades are not given in the supplier information. Check the Molex datasheet for these before specifying the product in a design.

Why OM4 and bend-insensitive construction matter

OM4 multimode fibre is widely used for high-speed data links over short and medium distances inside buildings. It is a common choice for connections between core, distribution and access layers in modern networks. Bend-insensitive construction is valuable in real installations, where cables must pass through tight spaces, vertical risers and the rear of cabinets. A bend-insensitive fibre helps reduce the risk of signal loss caused by a tight bend during installation or later maintenance.

Duplex SC connectors

Duplex SC connectors combine two fibres in a single connector body, which matches the transmit and receive pairs used by many network devices. The SC connector is a push-pull type that is easy to mate and remove, and it is a familiar format on fibre patch panels and transceivers. Using duplex connectors also keeps the number of connector interfaces lower than with two separate simplex connectors.

Typical uses

  • Backbone links between a main distribution frame and a server or equipment room
  • Connections from a fibre patch panel to a network switch or router
  • Fibre runs between floors or buildings in a campus network
  • Data centre and comms room cabling where Molex structured cabling is already installed
  • Replacement or extension of an existing multimode fibre link

Installation tips

Plan the route before pulling the cable. Keep bend radii within the limits given in the datasheet, and avoid pinching the assembly at cable ties or cabinet edges. Clean the connector end faces before mating, and use dust caps on any unused ports. Label both ends clearly so that the link can be traced during fault finding. Where the assembly will be patched into a panel, confirm that the panel accepts duplex SC adapters.

Choosing the right assembly

Before ordering, confirm the fibre count, multimode grade and connector type against the equipment at both ends of the link. If the project uses a different fibre grade, a different connector, or a different length, select an alternative article from the same range. If you are unsure which product matches your design, speak to a network cabling specialist who can check the layout and the active equipment requirements.

SKU AFR-00504L Category Brand:

Molex
AFR-00504L

Molex
12 Fiber Multimode OM4 BI Duplex SC Aqua Low Loss
Fibre assembly for structured cabling

Share this on your favourite channel:

Sign Up & Register

Mustek’s Infrastructure Technology Team are one of the largest suppliers of infrastructure technology in the country and on the continent. Register to become a reseller. Already a reseller?

Sign up for the latest pricelists, specials and offers.

Are you registered as a reseller?*
Area of interest?*

UPS Q&A

Keep up to date with the latest product developments from our divisions and outstanding solutions that will inspire you.

UPS Configuration Questionnaire

Ready to talk