Lenovo South Africa Channel Awards 2
Lenovo South Africa Channel Awards
Congratulations to our Server Team. Distributor of The Year!
ThinkSystem Tower Servers
Modernize to boost your business with Windows Server 2022.
Think Big. Think Lenovo. ThinkSystem Tower Servers.
Lenovo F1

INFRASTRUCTURE TEAM

+27 (0) 11 237 1000

INFRASTRUCTURE TEAM

Molex
Cat6 UTP LS0H Patch Cord 10M Red

Molex
Cat6 UTP patch cord, LS0H sheath, 568A/B wiring, 10m
Red colour

SKU PCD-02019-0C Category Brand:
Share

Molex Cat6 UTP LS0H Patch Cord, 10 Metre, Red

The Molex Cat6 UTP LS0H Patch Cord, 10M, red, is a factory-made patch lead for use in Cat6 structured cabling. It connects one piece of equipment to another, or a patch panel port to an active device such as a switch, router or wireless access point. Because the cord is prepared and ready to use, it saves time on site and removes the need to terminate plugs by hand.

The cord uses unshielded twisted pair (UTP) copper cable, the most common cable type for office and commercial networks. Its twisted pairs reduce interference between signal conductors, and the Cat6 rating places it in the category normally used for Gigabit Ethernet links in a structured system. The 10 metre length gives enough reach for most desk, wall outlet and cabinet arrangements without leaving large loops of spare cable.

Key features

  • Molex Cat6 unshielded twisted pair (UTP) patch cord
  • Length: 10 metres
  • Colour: red, for easy identification in patch fields
  • Wiring terminated to the 568A/B standard
  • LS0H (low smoke zero halogen) outer sheath
  • Ready-made with RJ45 plugs on both ends

Understanding the LS0H sheath

LS0H stands for low smoke zero halogen. A cable with this sheath produces relatively little smoke when it burns and does not release halogen gases. In an enclosed building, that can make escape and rescue easier and reduce damage to electronic equipment. Many building specifications and project briefs ask for LS0H cabling in public and occupied spaces, so the sheath type is an important part of choosing a patch cord.

Understanding the 568A/B wiring

568A and 568B are the two standard pin-out arrangements for RJ45 connectors. Both are widely used, and the key rule is that both ends of a straight-through patch cord use the same arrangement. Using a consistent standard across a site keeps installation predictable and makes future fault finding simpler for technicians.

Typical uses

  • Connecting a workstation or desk outlet to a network switch
  • Linking a patch panel port to an active device in a cabinet
  • Connecting IP phones, printers, cameras or access points
  • Interconnecting switches or other equipment in a rack
  • Offices, schools, clinics and retail sites with structured cabling

Why a colour-coded patch lead helps

In a busy cabinet, dozens of cords can look alike. Using red for a particular service, such as a specific VLAN, a camera link or a set of uplinks, makes faults quicker to trace and reduces the chance of unplugging the wrong lead during maintenance. Keeping a colour plan written down for the site helps every technician who works on the system later.

Choosing and installing the cord

Measure the route between the patch panel and the equipment, then allow a little extra for slack and bends, and choose the nearest standard length that covers it. Route the lead along cable management paths rather than across fronts of equipment, avoid sharp bends, and do not pull on the plug or the cable when unplugging. Label both ends if your site uses a labelling scheme. Where a project needs a particular length, colour or sheath, check the requirement against the product before ordering.

This Molex patch cord is a practical, neat and dependable choice for anyone building or extending a Cat6 network. Pair it with matching Molex panels and outlets to keep the whole link within one range.

SKU PCD-02019-0C Category Brand:

Molex
Cat6 UTP LS0H Patch Cord 10M Red

Molex
Cat6 UTP patch cord, LS0H sheath, 568A/B wiring, 10m
Red colour

Share this on your favourite channel:

Sign Up & Register

Mustek’s Infrastructure Technology Team are one of the largest suppliers of infrastructure technology in the country and on the continent. Register to become a reseller. Already a reseller?

Sign up for the latest pricelists, specials and offers.

Are you registered as a reseller?*
Area of interest?*

UPS Q&A

Keep up to date with the latest product developments from our divisions and outstanding solutions that will inspire you.

UPS Configuration Questionnaire

Ready to talk